Sangean WR-1 Especificações

Revision 1GBWR-2A

9 Power your radioAC operationBefore you plug the AC cord into the radio, be sure the AC voltage is correct. Insert the plug on the end of the suppl

GB10 Auto clock settinga. Radio data system (RDS)When you set the clock time using the RDS function, your radio willsynchronize its clock time whene

11b. Manual (if your don’t want to synchronized clock time with RDS CT)When choosing manual setting as the clock time setting of your radio, Radi

GB12 Date setting1. Press the Menu button to enter the setting.2. Rotate the Tuning control knob until ‘DATE SET’ is highlighted on the display.

13 D.S.T (Daylight Saving Time)1. Press the Menu button to enter the menu setting.2. Rotate the Tuning control knob until ‘DST OFF’ is appeared on

GB14 Antenna setup for AM receptionThe radio comes with built-in AM antenna which should be enough for normal listening. To improve the AM reception

15C. Presetting and recalling stations Presetting stations:1. Press the Power button to turn on your radio.2. Press the Band button repeatedly to

GB16 Setting up the tuning step increment1. Press the Menu button to enter the setting. 2. Rotate the Tuning control knob until FM xxkHz or AM xxkHz

17 Display modes - FMYour radio has a range of display options for FM radio mode.1. Repeatedly press and release the Info button to view the RDS

GB18 Alarm settingThere are two alarms which can each be set to wake you to AM/FM radio or buzzer alarm. The alarms may be set while the unit is in

1Read these instructions.Keep these instructions.Heed all warnings.Follow all instructions.Do not use this apparatus near water.Clean only with dry cl

193. Then the display will show the frequency options for the alarm. Rotate the Tuning control knob to select the desired option and press the

GB20b. Wake to buzzer alarm1. Before setting an alarm ensure the clock time is set. To enter the alarm setting, press and hold buzzer alarm button

21 When the alarm soundsWhen the buzzer alarm activates, the alarm will start softly and gradually increase in level. It will sound for 1 minute and

GB22 Snooze1. When the alarm sounds, press any button other than the Power button will silence the alarm for 5 minutes. “ “ will appear o

23 Display backlightTo turn on display illumination, press and release Light button ( ).By pressing and releasing Light button, you may also a

GB24 LoudnessYou can get compensation on lower and higher frequency for your radio by adjusting the Loudness function.1. Press the Menu button to en

25 AUX IN input level attenuationThe input level attenuation is to allow input level reduction once thesignal from external device is too strong.Not

GB26 Headphone useHeadphone use with this radio should be tted with a 3.5 mm jack plug. Insert the headphones plug into the jack in the front of th

27 Factory resetIf your radio fails to operate correctly, or some digits on the displayare missing/incomplete or you simply just want to restore to

GB28 SpecicationsPowered: AC 120V/60Hz/24W (US version)AC 230V/50Hz 24W (European version) Frequency Coverage:FM 87.50 – 108 MHzAM 520 – 1710 kHz (

GB2Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution

29REC outOutput impedance: 22Kohm DC IN12V/1A center pin positive (operational voltage 9-14V) AccessoriesFM F-terminal wire antennaAC power cordF-PAL

3

GB4SpeakerLight buttonBand buttonLCD displayPreset buttonsPower On / Off / Sleep buttonTuning control knobVolume / tone controlIR sensorMenu buttonMon

5Power On / Off / Sleep buttonNap buttonSelect buttonInfo buttonPreset buttonMute buttonLight buttonTuning up / down buttonTone control buttonVolume b

GB6Frequency / Time / Station displayRadio / Buzzer alarm indicatorDaylight Saving Time (DST) Sleep / Snooze statusRDS indicatorStereo indicatorMemory

7 Remote control functionsMany functions of the WR-2 radio can be operated using the remote control. Some operations require a longer press of th

GB8 Remote control battery replacement4. Replace the battery holder.IMPORTANT:The batteries should not be exposed to excessive heat such as sunshine